The Ministry of Road Transport and Highways has approved Rs 192.65 crore to stabilise eight landslide-prone stretches of NH-10 between Sevoke and Rangpo in Kalimpong district, the main road link to Sikkim. The eight sites total just over 2 km, so NH-10 slope protection is drilling, anchoring and concrete work. It is the third NH-10 sanction in under eight weeks.
What was announced
- Rs 192.65 crore approved by MoRTH for slope protection at eight vulnerable locations on the Sevoke-Rangpo section of NH-10, Kalimpong district.
- Darjeeling MP Raju Bista announced it on Friday, 20 November, after writing to Nitin Gadkari on 23 October.
- NHIDCL tendered eight locations on the same section in July on EPC mode: 2,180 m in all, estimated at Rs 148.67 crore before GST, with 24 months to build and 120 months of maintenance.
- Technical bids were opened on 6 November. No contractor has been named.
What the ministry approved
Bista said Gadkari had written to him with the approval. Sikkim Express and ETV Bharat both carried the figure and the eight locations; ETV Bharat put their length at 2.185 km, against 2,180 m in NHIDCL’s notice of 30 July. No report quotes a tender number, so we treat the match as very likely but unconfirmed. Neither says what the Rs 192.65 crore covers, so we have not set it against the tender estimate.
Which machines does this slope work call for?
Start with the rate. Rs 192.65 crore over 2.18 km is about Rs 88 crore a km; the tender estimate alone works out to about Rs 68 crore. Compare roughly Rs 40 crore a km for the Chutupalu ghat rebuild on NH-20 and Rs 156 crore a km on SRM Contractors’ landslide award in Pithoragarh. Very little of it goes into the carriageway.
The July tender schedules show where it goes: 38 mm self-drilling rock anchors rated at 400 kN (one site alone lists a minimum of 2,537), 300 mm micro piles drilled through soil and boulders, gabion walls passing 10,000 cubic metres at one site, concrete breast and retaining walls, shotcrete, rockfall barriers and subsurface drains. Those are minimums, and NHIDCL has since issued four corrigenda.
That means crawler drill rigs and grout pumps for anchors and piles, rock breakers to scale loose faces, compact and mid-size excavators for benching and gabions, and transit mixers with concrete pumps where a mixer cannot reach the wall. On a two-lane hill road, about 20 tonnes is the practical ceiling.
The EPC winner will probably bring its own drill crews. The sites sit in three groups across about 46 km, and short sites that far apart favour hiring excavators, tippers and mixers by the month. The biggest site, km 11.000 to 11.875, is 875 m long, 40 percent of the total, and will set the pace. The Teesta bridge at Sevoke and the Rangpo-Ranipool rebuild draw on the same small pool of hill crews. If all three move in 2027, drill-rig hire rates in Siliguri could firm. That is our reading; no report forecasts it.
Dates to note
- 30 July 2026: NHIDCL invited bids, EPC mode.
- 5 and 6 November 2026: bids closed and technical bids opened, on revised dates.
- Next: financial bid opening, the letter of award, then the appointed date that starts the 24-month clock.
- Monsoon rain usually halts slope work here, so the useful months run from about October to May.
Lining up plant for hill road work? See which machines highway packages run on in our road construction equipment guide, then compare models and prices before you hire or buy.
FAQ
Who will build the NH-10 slope protection works?
No contractor has been named. NHIDCL opened technical bids on 6 November. The financial bids and the award come next.
Where are the eight sites?
On the Sevoke-Rangpo section of NH-10 in Kalimpong district, between km 3.750 and km 50.140 by the tender’s chainage. They run from 105 m to 875 m long.
How long will the work take?
The tender allows 24 months of construction from the appointed date, followed by 120 months of maintenance by the same contractor.
Related on DesiMachines: NH-10 Rangpo-Ranipool upgrade: Rs 993.64 crore sanctioned for the Sikkim hill road
Source: Sikkim Express