In short: The L1 bidder is the one whose evaluated price is lowest among the bids that first cleared the technical stage — not necessarily the one who typed the smallest number. Corrections, tax treatment and loadings are applied before ranking, so L1, L2 and L3 are decided after the buyer has done arithmetic on your quote. Being L1 is also not the same as being awarded: the rate still has to be found reasonable, and where price discovery runs by reverse auction, the ranking only settles when the clock stops.

Most owners bidding for hire work learn the ranking the hard way — by watching a job go to someone whose quote looked higher on the day the financial bids opened.

The gap between “I quoted lowest” and “I got the work” is filled with steps that are all written down in the tender document, and almost never read before the bid is submitted.

What L1, L2 and L3 mean

After the financial bids are opened, the buyer arranges the qualifying bids from lowest to highest and labels them. The lowest is L1, the next L2, then L3. The letter stands for lowest and the number is simply the position.

Two things about that list matter more than the labels.

The first is who is on it. Only bids that cleared technical evaluation get ranked. A bidder who quoted the lowest figure in the room but whose experience certificate or machine schedule did not satisfy the conditions is not L1 — that bid is out, and the ranking happens without it. The two-part submission we cover in the bidding guide is what decides whether your price is ever seen at all.

The second is what the ranking is done on.

Evaluated price, not the number you typed

Ranking uses the evaluated price — your quote after the buyer has applied whatever the tender allows it to apply.

Adjustment What it does to your quote
Arithmetic correction Rate times quantity is recomputed. Where words and figures differ, the tender says which prevails — often the rate in words.
Tax treatment Bids are brought to a common basis so that a quote stated inclusive is comparable with one stated exclusive.
Loading for deviations If you took a deviation from the payment or delivery terms and it was permitted, the buyer may load a cost onto your price for comparison.
Unbalanced items Rates that are very high on early items and very low on later ones draw scrutiny, and can cost you the bid even when the total is lowest.

This is why two bidders can enter the same total and finish at different ranks. It is also why a conditional bid is dangerous: conditions that the tender does not permit can get the bid rejected outright rather than merely loaded.

Can the buyer negotiate with the L1 bidder?

This is the most-asked question of the lot, and the honest answer is that it depends on the buyer’s own rules.

The principle applied across public procurement is that negotiation, where it is allowed at all, is conducted with L1 only. The reason is straightforward. If a buyer could go down the list and invite better numbers after the prices were public, no sealed bid would mean anything and every bidder would quote high in the expectation of a second round.

So negotiation tends to be treated as exceptional rather than routine, reserved for situations such as a single bid or a rate that looks out of line with the estimate, and it usually needs approval from a level above the tendering officer.

What follows for you is practical. Do not price your bid on the assumption that there will be a negotiation stage where you can improve. Bid the number you can actually execute at. If you are called for negotiation as L1, treat it as a request to justify your rate — bring the rate analysis, not just a willingness to drop.

When price discovery runs as a reverse auction

On the government marketplace and on several e-procurement platforms, the sealed financial bid is followed by a live auction in which bidders reduce their offers within a time window. The lowest standing offer when the clock stops becomes L1.

Three things decide whether that room is profitable for you.

The decrement. Each new bid must improve on the standing lowest by at least a set amount. Know it before you enter, because it sets how fast the price can fall.

Your floor. Work out, before the auction opens, the rate below which the job stops paying — machine EMI, operator, diesel, maintenance, transport to site, and the idle days between fronts. Write that number down. The whole design of an auction is to make you find out where your floor is by passing it.

The extension rule. A bid placed near the end usually extends the clock, so the auction rarely stops when you expect it to.

If you have not costed a machine hour properly, an auction is the most expensive place to discover it. Our equipment rental rate card sets out what a day rate has to cover before it earns anything.

Being L2 is not a queue

Owners often treat L2 as next in line. It is not a position with rights attached.

If L1 withdraws or fails to furnish the security or sign the agreement, the buyer forfeits that earnest money and then chooses — approach the next ranked bidder, or retender. Which route it takes depends on its rules, the price gap and how urgent the work is. Walking away after an award is also one of the standard triggers for blacklisting, so the cost is rarely just the deposit.

If you are approached as L2, you are being asked whether you will do the work, usually at the L1 rate. That is a fresh commercial decision. Run it through the same arithmetic you used the first time, because the rate that made sense for someone else’s fleet may not make sense for yours.

The fees, and which one comes back

Two payments get confused constantly.

The tender fee is the cost of participating — a document or processing charge, generally non-refundable, and it does not come back because you lost.

The earnest money deposit is security. It is returned to unsuccessful bidders and is forfeited if you win and then fail to take the work up. Small enterprises are often exempt from it, which the bidding guide covers, and registration on the government marketplace is where many owners meet both for the first time.

Once you win, the money moves again — into the security the contract asks you to furnish, usually a performance bank guarantee, which carries its own cost and its own release problems.

The bottom line

L1 is a rank produced by arithmetic on your quote, awarded only if the rate stands up as reasonable, and it is available only to bids that cleared the technical stage first. The bidders who win consistently are the ones who qualify cleanly, quote a number they can execute, and know their floor before an auction starts.

Check what your capacity actually allows before you chase a large job — our note on the bid capacity formula covers that ceiling, and current work is listed on the tender opportunities page.

Last updated: 28 August 2026. Rates, schemes, specifications and prices change — confirm current terms with the OEM, dealer, bank or insurer before deciding. Evaluation rules, negotiation powers and auction settings differ between buyers and between tenders; confirm them in the tender document that applies to you.